整本手册下载H3C S9500 LSB1FW8DB1 单板手册(V1.02)
3端口10/100BASE-TX RJ45电接口及8端口1000BASE-X-SFP光接口板 – LSB1FW8DB1
1 单板标识
前面板右上角标有丝印：FW8DB，用来标识该单板。
2 单板简介
FW8DB单板上从左到右依次排列有8个1000Base-X接口、Console口、AUX口、3个10/100Base-TX接口和4个状态指示灯（ATTACK、ACT、ALM、RUN）。
|
属性 |
规格 |
|
接口连接器类型 |
RJ45，SFP/LC |
|
接口数量 |
l 1个Console口，支持本单板的本地配置管理 l 1个AUX口，支持本单板的远程拨号配置管理 l 3个10M/100M以太网电接口 l 8个1000M SFP光接口 |
|
接口传输速率 |
l Console口：9600bit/s l AUX口：300bit/s～115200bit/s l 10/100Base-TX接口：10M/100Mbit/s，半/全双工 l 1000Base-X-SFP接口：1000Mbit/s，全双工 |
|
可选用线缆及最大传输距离 |
l Console口：普通异步串行口电缆，传输距离≤15m l AUX口：普通异步串行口电缆，传输距离≤15m l 10/100Base-TX接口：5类双绞线，传输距离100m l 1000Base-X-SFP接口属性请参见表2 |
|
单板适用的机型 |
S9502/S9505/S9508/S9508V/S9512 |
|
单板适用的主机软件版本 |
1321及以上版本 |
可选用的SFP模块类型及其属性见下表。
表2 SFP模块属性
|
SFP模块名称 |
中心波长 |
接口连接器类型 |
接口光纤规格 |
光纤最大传输距离 |
|
1000BASE-SX-SFP |
850nm |
LC |
50/125µm多模光纤 |
550m |
|
62.5/125µm多模光纤 |
275m |
|||
|
1000BASE-LX-SFP |
1310nm |
9/125µm单模光纤 |
10km |
|
|
1000BASE-LH-SFP |
40km |
|||
|
1000BASE-ZX-LR-SFP |
1550nm |
|||
|
1000BASE-ZX-VR-SFP |
70km |
|||
|
1000BASE-ZX-UR-SFP |
100km |
3 升级方式
用户可通过以下方式对FW8DB单板进行升级：
(1) 通过Boot菜单本地升级
l 通过Console口利用XModerm协议进行升级
l 通过百兆以太网口Ethernet 3利用TFTP协议进行升级
(2) 通过命令行远程升级
l 通过百兆以太网口（Ethernet 1～Ethernet 3中任意一个）利用FTP协议进行升级
l 通过百兆以太网口（Ethernet 1～Ethernet 3中任意一个）利用TFTP协议进行升级
注意：
FW8DB单板的升级只能在自身的Console口或以太网口下进行，而不能通过S9500主控板。
4 注意事项
如主机软件版本不匹配，请联系该设备的销售商或集成商获取相应的主机软件版本；
单板安装说明及主机软件版本的升级方法请参见《H3C S9500系列路由交换机 安装手册》相关章节。
单板种类或规格可能随产品版本的变更而改变，请从公司网站http://www.h3c.com.cn主页上的“文档中心”获取最新资料。
杭州华三通信技术有限公司
3 x 10/100BASE-TX Electrical Interface + 8 x 1000BASE-X-SFP Optical Interface Card – LSB1FW8DB1
1 Card Identifier
The silkscreen FW8DB is printed at the upper right corner of the front panel, and is used to identify the card.
2 Specifications
On the front panel of FW8DB, eight 1000Base-X interfaces, Console port, AUX port, three 10/100Base-TX interfaces, and four status LEDs (ATTACK, ACT, ALM, RUN) are arranged from left to right.
Table1 Card specifications
|
Item |
Specification |
|
Connector |
RJ-45, SFP/LC |
|
Interface |
l One Console port supporting the local configuration management l One AUX port supporting remote dialup configuration management l Three 10/100 Mbps electrical interfaces l Eight 1000 Mbps SFP optical interfaces |
|
Transmission rate |
l Console port: 9600 bps l AUX port: 300 bps to 115200 bps l 10/100Base-TX interface: 10 Mbps, half/full duplex l 1000Base-X-SFP interface: 10000 Mbps. Full duplex |
|
Cable and maximum transmission distance |
l Console port: Asynchronous serial cable with maximum transmission distance of 15 meters l AUX port: Asynchronous serial cable with maximum transmission distance of 15 meters l 10/100Base-TX interface: Category 5 UTP with maximum transmission distance of 100 meters l 1000Base-X-SFP interface: Refer to Table2 for details |
|
Applied to |
S9502/S9505/S9508/S9508V/S9512 |
|
Host software version |
Version 1321 or above |
For supported SFP modules, refer to the following table.
|
Optional SFP module |
Central wavelength |
Connector type |
Fiber specifications |
Maximum transmission distance |
|
1000BASE-SX-SFP |
850nm |
LC |
50/125µm multi-mode optical fiber |
550 m |
|
62.5/125µm multi-mode optical fiber |
275 m |
|||
|
1000BASE-LX-SFP |
1310nm |
9/125µm single-mode optical fiber |
10 km |
|
|
1000BASE-LH-SFP |
40 km |
|||
|
1000BASE-ZX-LR-SFP |
1550nm |
|||
|
1000BASE-ZX-VR-SFP |
70 km |
|||
|
1000BASE-ZX-UR-SFP |
100 km |
3 Upgrading FW8DB
To upgrade the FW8DB, follow one of the ways:
1) Local upgrade by the Boot menu
l Use the XModem protocol through the Console port
l Use the TFTP protocol through the port Ethernet 3
2) Remote upgrade by the command line
l Use the FTP protocol through the Ethernet port (anyone among the Ethernet 1 through Ethernet 3)
l Use the TFTPP protocol through the Ethernet port (anyone among the Ethernet 1 through Ethernet 3)
Caution:
You can only upgrade the FW8DB through its own Console port or Ethernet port, but not the SRPU.
4 Note
If the host software version does not match the one applicable to the card, contact the vendor or the integrator for the right version.
For the introduction of card installation and host software upgrade, see the related part in H3C S9500 Series Routing Switches Installation Manual.
As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com.
Hangzhou H3C Technologies Co., Ltd.
