1端口OC-192c-POS光接口板 – LSB1UP1CA0

1  单板标识

前面板右上角标有丝印：UP1CA，用来标识该单板。

2  单板简介

                                                                                                                                                                                  表1 单板属性

属性	规格
接口连接器类型	XFP/LC
接口数量	1个10G POS光接口
接口传输速率	10Gbps
单板适用的机型	S9502/S9505/S9508/S9508V/S9512
单板适用的主机软件版本	1272及以上版本

 

可选用的XFP模块类型及其属性见下表。

                                                                                                                                                                            表2 XFP模块属性

XFP模块名称	中心波长	XFP模块提供的用户接口连接器类型	接口光纤规格	光纤最大传输距离
10GBase-SR/SW-XFP	850nm	LC	50/125µm多模光纤	对于62.5um MMF w/ 160MHz*km光纤，最大传输距离26M； 对于50um MMF w/ 500MHz*km光纤，最大传输距离82M； 对于50um MMF w/ 2000MHz*km光纤，最大传输距离300M；
10GBase-LR/LW-XFP	1310nm		9/125µm单模光纤	10km
10GBase-ER/EW-XFP	1550nm		9/125µm单模光纤	40km

 

3  注意事项

如主机软件版本不匹配，请联系该设备的销售商或集成商获取相应的主机软件版本；

单板安装说明及主机软件版本的升级方法请参见《H3C S9500系列路由交换机  安装手册》相关章节。

单板种类或规格可能随产品版本的变更而改变，请从公司网站http://www.h3c.com.cn主页上的“文档中心”获取最新资料。

 

 

杭州华三通信技术有限公司

 

                                                        1-Port OC-192c-POS Optical Interface Card – LSB1UP1CA0

1  Card Identifier

The silkscreen UP1CA is printed at the upper right corner of the front panel, and is used to identify the card.

2  Specifications

Table1  Card specifications

Item	Specification
Connector	XFP/LC
Port quantity	One 10G POS optical port
Transmission rate	10Gbps
Applied to	S9502/S9505/S9508/S9508V/S9512
Host software version	Version 1272 and above

 

For supported XFP modules, refer to the following table.

Table2  XFP Module Attribute

XFP module	Central wavelength	Connector	Matching cable	Transmission segment
10GBase-SR/SW-XFP	850 nm	LC	50/125 µm multimode optical fiber cable	For 62.5um MMF w/ 160MHz*km optical fiber cable: 26M; For 50um MMF w/ 500MHz*km optical fiber cable: 82M; For 50um MMF w/ 2000MHz*km optical fiber cable: 300M;
10GBase-LR/LW-XFP	1310 nm		9/125 µm single mode optical fiber cable	10 km (6 mi)
10GBase-ER/EW-XFP	1550 nm		9/125 µm single mode optical fiber cable	40 km (about 25 mi)

 

3  Note

If the host software version does not match the one applicable to the card, contact the vendor or the integrator for the right version.

For the introduction of card installation and host software upgrade, see the related part in H3C S9500 Series Routing Switches Installation Manual.

As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com.

 

 

Hangzhou H3C Technologies Co., Ltd